Wilkerson PC6 Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Wilkerson PC6. Wilkerson PC6 User Manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SCREW
ADJUSTING
KNOB
ASSEMBLY
LOCK KNOB
PANEL
MOUNT
NUT
TAMPER
RESISTANT
KIT (optional)
DIAPHRAGM
ASSEMBLY
REGULATING
SPRING
ADJUSTING
STEM
ASSEMBLY
VALVE STEM
O-RING
BODY
NNR
BOWL
O-RING
FILTER
ELEMENT
GASKET
ADAPTER
NNR
VALVE SPRING
O-RING
BAFFLE
NNR
FLEX-DRAIN™
(plastic bowls only)
O-RING
AUTOMATIC
MECHANICAL
DRAIN
O-RING
BOWL
INSERT
TRANSPARENT
BOWL
BOWL
GUARD
SIGHT GAUGE
KIT
NUT
(for use with
Auto. Mechanical
Drain)
SCREW
RETAINER
METAL
BOWL
INSERT
RETAINER
PETCOCK
(for metal
bowls only
)
INSTALLATION
Install the Filter/Regulator as close as possible to the application. The
inlet port is marked with an arrow cast into the body to indicate the
direction of flow. Gauge ports (1/4") are provided in either side of the
body for installation of a gauge or use as an additional outlet port.
Plug unused port(s). System piping should be same size as regulator
porting. In systems with a cyclic demand, the regulator should be
located upstream of cycling device.
OPERATION
Maximum pressure rating is 150 psig (10 bar) for transparent
plastic bowls, and 200 psig (14 bar) for metal bowls.
Temperature range is 32°F to 125°F (0°C to 52°C) for transparent
plastic bowls, and 32°F to 150°F (0°C to 65.5°C) for metal bowls.
Before turning on the supply air pressure, turn the adjusting knob
counterclockwise until there is no load on the regulating spring. Turn
on the supply air pressure and then turn the adjusting knob clockwise
until the desired secondary pressure is reached. To avoid minor
readjustment after making a change in pressure setting, always
approach the desired pressure form a lower pressure. When reducing
from a higher to a lower setting, first reduce to some pressure less
than that desired and then increase to the desired pressure.
SEE REVERSE SIDE FOR LIST OF MATERIALS
UNSUITABLE FOR USE WITH POLYCARBONATE BOWLS
MAINTENANCE
1. The regulator can be disassembled for servicing without removal
from line.
2. DEPRESSURIZE UNIT BEFORE REMOVING GUARD AND/OR
BOWL.
3. TO DISASSEMBLE: shut off air to the filter/regulator and vent air
line on both sides of unit. Turn adjusting screw counterclockwise
to relieve spring compression. Remove knob, cover cap, screw
cover, and spring. Diaphragm assembly can now be removed.
4. To remove valve from bottom of unit, remove bowl. Remove baffle
and filter element exposing hex nut on adapter assembly.
Remove adapter assembly, valve and spring.
(continued on reverse side)
NNR = NOT NORMALLY REPLACED
WARNING
To avoid unpredictable system behavior that can cause personal injury
and property damage:
• Disconnect electrical supply (when necessary) before installation,
servicing, or conversion.
• Disconnect air supply and depressurize all air lines connected to
this product before installation, servicing, or conversion.
• Operate within the manufacturer’s specified pressure, temperature,
and other conditions listed in these instructions.
• Medium must be moisture-free if ambient temperature is below
freezing.
• Service according to procedures listed in these instructions.
• Installation, service, and conversion of these products must be
performed by knowledgeable personnel who understand how
pneumatic products are to be applied.
• After installation, servicing, or conversion, air and electrical supplies
(when necessary) should be connected and the product tested for
proper function and leakage. If audible leakage is present, or the
product does not operate properly, do not put into use.
• Warnings and specifications on the product should not be covered
by paint, etc. If masking is not possible, contact your local
representative for replacement labels.
!
!
WARNING
Product rupture can cause serious injury.
Do not connect regulator to bottled gas.
Do not exceed maximum primary pressure rating.
Installation & Service Instructions
83-861-000
Precision Air Pressure Regulator
Type PC6B Filter / Regulator
ISSUED: April, 2006
Supersedes: July, 2004
Doc.# 83861000, ECN# 060299, Rev. 4
Richland, MI 49083 Tel: (269) 629-5000
1
2
Résumé du contenu
Page 1 - WARNING
SCREWADJUSTINGKNOBASSEMBLYLOCK KNOBPANELMOUNTNUTTAMPERRESISTANTKIT (optional)DIAPHRAGMASSEMBLYREGULATINGSPRINGADJUSTINGSTEMASSEMBLYVALVE STEMO-RINGBOD
Page 2 - CAUTION
REPAIR KITS AND REPLACEMENT PARTSSELF-RELIEVING REPAIR KIT (includes self-relievingdiaphragm assembly, valve stem, valve spring,filter element, and bo
Produits connexes et manuels pour Matériel Wilkerson PC6
(2 pages)
(6 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.955 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels